Download Free NACE NACE-CIP1-001 Exam Questions & Answer
Online VALID NACE-CIP1-001 Exam Dumps File Instantly
NEW QUESTION # 57
Silicone coatings are typically:
- A. Used as a sacrificial primer
- B. Applied in very' thin films
- C. Used strictly in immersion service
- D. Applied in very thick films
Answer: B
NEW QUESTION # 58
Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply
- A. Measuring ditty, tacky, or soft films
- B. Failing to determine the base metal reading (BMR)
- C. Rotating the dial too fast when taking measurements
- D. Taking measurements too far from the edge of a surface
Answer: A,B,C
NEW QUESTION # 59
If inspectors identify issues of non-conformance during an inspection, they should
- A. wait until the final report is being prepared to identify the issues in writing so they are fully documented
- B. perform additional tests secretly to ensure there are no other potential issues at the site
- C. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
- D. instruct the contractor's personnel in how to correct the issue so the project is not delayed
Answer: C
NEW QUESTION # 60
As a NACE Coating Inspector your responsibility with respect to safety is to:
- A. Act in accordance with the site safety requirements and set an example
- B. Assume the role of the Safety Inspector
- C. Check the credentials of the Safety Officer on site
- D. Check the PPE used by the Applicators
Answer: A
NEW QUESTION # 61
Stripe coats are generally applied to:
- A. a), b), and c)
- B. Edges and corners
- C. Complex geometric shapes
- D. Welds
Answer: A
NEW QUESTION # 62
Corrosion generally occurs at which of the following sites:
- A. Electrolyte
- B. Metallic pathway
- C. Anode
- D. Cathode
Answer: C
NEW QUESTION # 63
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:
- A. Level 2
- B. Level 3
- C. Level 1
- D. Level 4
Answer: B
NEW QUESTION # 64
Passivation can best be described as:
- A. A coating layer applied to the surface to inhibit corrosion
- B. Treating metal with a liquid inhibiter
- C. Complete elimination pf the corrosion process
- D. A protective metallic oxide surface layer that slows corrosion
Answer: D
NEW QUESTION # 65
ISO SA 3 is directly equivalent to:
- A. NACE No. 1/SSPC SP 5
- B. NACE No. 3/SSPC SP 6
- C. NACE No. 2/SSPC SP 10
- D. None of the above
Answer: D
NEW QUESTION # 66
Whenever dissimilar metals must join, the most common practice is to
- A. provide cathodic protection to prevent corrosion,
- B. coat all connected dissimilar metals.
- C. provide anodic protection to prevent corrosion.
- D. avoid coating all connected dissimilar metals.
Answer: B
NEW QUESTION # 67
You ate the NACE Inspector on a job where NACE No. 2/SSPC - SP 10 has been specified. You are finding the Contractor is leaving mill scale on the on surface and as a result you have been rejecting the blast. The Contractor is very upset and has told you that the standard permits up to 5% of the mill scale to remain and still be in be in compliance with the standard.
Your FIRST preferred course of action is to:
- A. Shut the job down
- B. Call your supervisor
- C. Review the relevant standard with the Contractor
- D. Permit coating to take place so as not to lose the blast
Answer: C
NEW QUESTION # 68
Prior to using Inspection Tools the inspector must:
- A. a), b) & c)
- B. Be trained on how to use the instrument
- C. Ensure the instrument is within calibration parameters
- D. Read the manufactures' instructions
Answer: A
NEW QUESTION # 69
The main responsibilities of the inspector are to
- A. direct and perform the work stated in the specification.
- B. demonstrate to the contractor how to apply the coating.
- C. observe and report the quality of the work performed.
- D. observe and direct the work of the contractors.
Answer: C
NEW QUESTION # 70
Good records can provide maintenance departments with detailed information about ALL of the following EXCEPT
- A. what materials were used.
- B. when the coating will be reapplied.
- C. how the item was coated.
- D. what items were coated.
Answer: C
NEW QUESTION # 71
Upon arrival of coating materials, the inspector should
- A. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations.
- B. observe and document the amount of material and batch numbers.
- C. observe aryl document that the applicator WFT at regular intervals during application.
- D. observe and document time frame and environmental conditions between each coat.
Answer: B
NEW QUESTION # 72
Check abrasive blast pressure with a
- A. nozzle aperature gauge
- B. needle pressure gauge
- C. replica tape
- D. surface comparator
Answer: B
NEW QUESTION # 73
Safety Data Sheets must be carefully reviewed by:
- A. The Inspection personnel
- B. The Application personnel
- C. All personnel involved in the job
- D. The Owner's personnel
Answer: C
NEW QUESTION # 74
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 105 Gauge Readings resulting in 35 Spot Measurements
- B. 225 Gauge Readings resulting in 75 Spot Measurements
- C. 45 Gauge readings resulting in 15 Spot Measurements
- D. 75 Gauge Readings resulting in 25 Spot Measurements
Answer: B
NEW QUESTION # 75
A magnetic pull-off type gauge is a good choice when:
- A. When an intrinsically safe tool is required
- B. Performing an adhesion test
- C. Accuracy is not required
- D. When working on non-ferrous metals
Answer: A
NEW QUESTION # 76
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Advise the Contractor of your readings
- B. Call your supervisor
- C. Advise the Contractor he can proceed
- D. Advise the Contractor he cannot proceed
Answer: A
NEW QUESTION # 77
Prior to the pre-job conference you notice that the Inspection and Test Plan does not require a hold point after surface preparation and coating application. In speaking with the owners' representative in advance of the meeting you sense he/she does not understand the importance of the hold point.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Default to the owner's Inspection and Test Plan
- B. Bring the matter up at the pre-job conference
- C. Gather data and attempt to meet with the owner's representative in advance of the pre-job conference
- D. Meet separately with the coating manufactures' representative and coating application company in advance of the pre-job conference
Answer: B
NEW QUESTION # 78
Removal of surface contaminants is done by:
- A. Waterjetting
- B. Scarifying
- C. A combination of methods
- D. Abrasive blasting
Answer: C
NEW QUESTION # 79
ASTM Standards are applicable:
- A. In Asia
- B. In the USA
- C. When specified
- D. In North America
Answer: C
NEW QUESTION # 80
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Review the NACE Attestation prior to making a decision
- B. Advise the prospective employer that you cannot accept the position
- C. Meet with the prospective employer to determine the scope of your role
- D. Accept the assignment without hesitation
Answer: C
NEW QUESTION # 81
The initial steel condition is important to the NACE Inspector because:
- A. If the steel is pitted more coating will be required
- B. Less abrasive is need if the mill Scale s gone
- C. It affects the final appearance after blasting
- D. The Inspector may have to reject the Steel
Answer: D
NEW QUESTION # 82
......
NACE-CIP1-001 Exam Dumps For Certification Exam Preparation: https://www.testpdf.com/NACE-CIP1-001-exam-braindumps.html
100% Pass Guaranteed Download CIP Level 1 Exam PDF Q&A: https://drive.google.com/open?id=14AaMaOsDdq1Kd2IzKPLCUeyFjA6dZGQq
